but the issue is you can't access storage?ĭid you do anything besides flash the debug boot img to your phone. Which H860 M build are you on at this point? 10A, 10B etc?Īnd ADB root is working on your phone. you used dirtysanta to exploit your phone and install the ADB root debug boot img? was this for the downgrade from N to M? or once you downgraded to M you tried UPPERCUT?Īnd once on M. You mention "Uppercut was working at that time". P.S I use official cable, tried many KDZ from different regions, tried It on a VM, my PC, my laptop and on a friends laptop and still no luck I'm not the only one with this problem, and apparently someone who had this exact same problem fixed it by using his brother's H860 to work with LG UP and then put his phone for the update, I'm still searching for someone in my school who has the same model as mine to test lol Oh too bad :/, I'm using a H860 and after using, I lost access to my storage (It didn't work on N so I downgraded to MM and Uppercut was working at that time) but still got Root.Īlready tried LG UP 1.10 and 1.11 with DLL and registery alteration, It detects my model, but It stops from working and gives an error at 4% (usb connection established), on LG UP 1.14 It says unknown model no mater what I do.Īfter that I tried a couple of things, like asking someone on MM to give me his build.prop and replace mine (Ofc I backup my original one) and still no luck, but for some reason, with his build.prop my phone laggs less (one of the problems with no storage)Īlso tried LG flash tool 2016 no luck either "(S) failed to load" error message, tried an update with LG Bridge but it doesn't detect MTP (I enabled it ofc), but in Download mode, It detects my phone, downloads the update, but can't apply it, maybe It need the phone to be On and not on download modeįrom my experience, the only way I see to get out of this is either custom recovery (or a way to access H860 MM recovery since we can't bypass the dead android) to be able to push an update file from ADB or someone stumbles upon some solution. and answering your initial question got me thinking about it I'm just taking this time to respond to multiple things at once. Or manually file swapping and possibly editing the registry.Īlso, this is not me ranting at anything you said or anything. To use 1.11 you'd need to use the "original methods" that required a dll msi installer for each model. but such time and testing won't be put into these public releases and requires feedback from the public. When building these for clients there is lots of testing going into a specific device or set of devices under specific conditions. These XDA public releases are trying to target a large group of devices in a single build. and then new builds can be made from there. which exact model and software version was the phone on?Īnd if enough people can report BOTH success and failure details with UPPERCUT we'd have more info on exactly what is and isn't supported on this 1.0.0.0 build. If TOT or KDZ did flash successfully but the phone won't boot into android, have you tried a factory reset?ĭid LGUP work? Great. Was phone rooted and bootloader changes attempted?Īny more specifics on the conditions leading up to flashing this KDZ.? Was bootloader unlocked on an early M build and only the rom was updated while the bootloader wasn't updated? Was bootloader unlocked and have bootloaders been swapped? Model info can be determined by such things as the build.prop and misc partition, has either possibly been altered? Unfortunately, I do not have any other models to test with and can only take note of some situations people report.īut much of the info reported is not detailed enough.įlashing from which exact sw version to sw version? Unable to replicate similar outcomes on my H830 and am able to flash on both M and N with no issue in all my testing. we'll see.įor any cases where the G5 is on N or a later M build and still not detected. not sure if I'll be moving backwards tho. and N to future N builds.Ī new UPPERCUT build would be needed to try and target devices on earlier builds. UPPERCUTs XDA release was mainly targeted for flashing a device from the latest M build. higher seem to have a higher success rate w/UPPERCUT. It seems that there are some G5 users (and possibly other models) that are on early M builds and are showing as "Unknown model".Įarly M builds being 10A, 10C, 10D, 10E. I never released an UPPERCUT for 1.11 on XDA.Įarlier UPPERCUT EXEs were mainly just UI differences and added nothing that isn't supported in the currently released build.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |